|A tunnel is an underground passage for a road or similar.|
|Used on these elements|
|Documented values: 2|
|Tools for this tag|
tunnel=* is used for roads, railway line, canals etc that run underground (in ).
For some grade separated crossings it may however be debatable if the lower way is in the tunnel or if the upper way is on a bridge=*. In general, if the lower way is long and surround by earth it is almost certainly a tunnel; and if the lower way is short and the upper way is supported on concrete, brick on metal pillars / beams then that is almost certainly a bridge. There are however situations where it is a matter of personal judgement, but it is preferred to either tag the lower way as tunnel or the upper way as a bridge but not both.
For covered passages which are open on one side, often ways underneath a building, use covered=* in place of tunnel=*. One exception are landslide/avalanche protectors on mountain roads which are tagged as tunnel=avalanche_protector.
Where the water from a smaller stream, drain or even cattle crossing passes under a way structure or a building consider using tunnel=culvert in place of the tunnel=yes used for accessible and larger tunnels for roads or railways.
When the waterway=* runs underground for a considerable distance, you can use tunnel=flooded especially when the duct isn't designed to be safely accessible in operation or man_made=pipeline for sections built with tube assemblies.
Power cables (power=cable) buried underground should not be tagged as tunnels. The location of a buried cable may optionally be tagged as location=underground/underwater. However if the cable is located inside a self-supporting tunnel it may be tagged as tunnel=yes. Such dedicated power tunnels are sometimes found in large cities.
How to map
- split the way in question at the points were the tunnel starts and ends and add the tunnel tag. It is best to avoid having a tunnel continue to a junction that is not in a tunnel by splitting the way prior to the junction.
- most tunnels should be tagged with layer=-1 or another suitable negative value (exception: tunnel=building_passage). For metros/subways or other very long ways it is often convenient to use layer=-2 to accommodate underground passages for pedestrians between the tunnel and the surface.
- Where the approach to the tunnel is in a cutting this can be identified with cutting=yes. Note that a layer=* tag is not desired on a cutting or embankment unless there are several layers of objects that need to be differentiated.
tunnel=building_passage should not normally have a layer assigned as there is no clear above/below relation to the building but a layer may be required when there are several layers of building passages.
If the tunnel has a name this can be specified using tunnel:name=* although there is still some debate on the best method to include a name of the tunnel as discinct from the road/railway etc that goes through it. lit=* can be included to provide information about any lighting in the tunnel (or not).
Ways that go through a building and have walls on both sides should be tagged with tunnel=building_passage.
- the building and the way should have shared nodes at the entry and exit points of the building.
- the way is split at the entry and exit nodes and only the part covered by the building is tagged with tunnel=building_passage.
- the layer should be the same as the layer of the building, with the above mentioned exception when several tunnels are passing on different levels. So if the building doesn't have a layer tag, the way should not have one either.
When building_passage should not be used:
It is not meant to be used for indoor mapping. The walls at both sides (and the top) of the tunnel are considered outer walls of the building, which can have entrances that lead into it (This proposal doesn't cover entrances inside building passages). For indoor mapping highway=corridor or indoor=yes can be used. It is also not meant for ways that go through something else than a building.
A variant of covered=arcade is tunnel=avalanche_protector and should be used in case of tunnels alongside mountains. These constructions stand for themselves and are not attached to a building. Their purpose is to protect the highway or railway from avalanches and landslides. Use avalanche_protector:left=open or avalanche_protector:right=open to define which side of the way is open ("open" in case of avalanche protectors means, that light and air can enter on that side).
Mapnik draws tunnels on highways with dotted outlines and a lighter fill color for the road and with curved color transitions on tunnel entrances.
- Proposed_features/building_passage - accepted proposal
- Relations/Proposed/Bridges_and_Tunnels - group multiple tunnel elements with a relation
- Proposed features/man_made=tunnel - simple way of indicating the outline of a tunnel and grouping together all features for that tunnel