|power = tower|
|For towers or pylons carrying high voltage electricity cables. Normally constructed from steel latticework.|
|Rendering in openstreetmap-carto|
|Used on these elements|
|Status: in use|
|Tools for this tag|
For big towers or pylons carrying electricity cables. Normally constructed from steel latticework and carry high voltage electricity cables.
How to Map
Detailed tower tagging
You can add additional information about the tower using the following tagging scheme.
|The default value is steel.|
|This tag describes the construction type of a tower. |
For steel towers (or if no material tag is specified) the default value is lattice. For wooden or concrete towers the default is solid.
|height||*||The height in meter of the tower if known.|
|colour||*||The colour(s) of a painted tower, e.g. colour=red/white for tower painted red and white to make it better visible to pilots.|
This tag describes the design of the tower. The main parameters are the number and positions of cross-arms. Cross-arms which only serve as support for earth wires should not be considered. See examples with suggested values below.
|design||one-level||A tower having cross-arms at a single level only.|
|design||two-level||A tower having cross-arms at two levels.|
|design||donau||A common sub-type of the two-level tower. It is characterized by having one conductor on each side at the upper level and two conductors at each side on the lower level. The "Donaumast" is widely used in central Europe.|
|design||three-level||A tower having cross-arms at three levels.|
|design||barrel||A common sub-type of the three-level tower. It is characterized by the middle level cross-arms being longer than the upper and lower cross-arms giving the conductor arrangement a barrel-like shape.|
|design||asymmetric||A two- or three-level tower carrying only one circuit and having the conductors arranged in an asymmetrical layout.|
|design||triangle||A sub-type of the asymmetric tower. It has cross-arms at three levels providing a triangular arrangement of the conductors.|
|design||flag||A sub-type of the asymmetric tower. All conductors are located at one side. The tower typically has no or only rudimentary crossarms. This tower type is usually used as an angle tower.|
|design||donau;one-level||A three-level combination tower effectively being a Donau tower having an additional lower level, often used for circuits of a lower voltage than those at the upper levels. This tag better describes the design than just using "three-level". Similar tag values may be used for other designs having an additional lower level.|
|A tower having cross-arms at four or more levels. These tall towers may carry four or more circuits.|
|design||delta||A y-shaped tower having a horisontal cross-beam between the two top structures. All conductors are attached to the cross-beam. It is mostly used for a single circuit.|
|Delta tower having two or three cross-beams. Suitable for three circuits.|
|design||y-frame||Similar to delta tower but there is no horisontal cross-beam between the two top structures. The middle conductor is supported directly by the top structures.|
|design||x-frame||A variation of the y-frame tower having two legs. It is suitable for carrying a second lower voltage circuit on a crossbeam below the joint.|
|design||h-frame||A tower type having two (or more) separate pylons or poles connected by a beam to which the conductors are attached. The cross-beam extends beyond the vertical structures such that not all conductors are located between the vertical structures. The portal tower is mostly used for a single circuit.
Also known as pi-poles due to their resemblance to the Greek letter pi (π).
|Designs like the h-frame tower, but having cross-beams at two or three levels.|
|design||guyed_h-frame||A guyed version of the h-frame tower supported by guy wires, common in e.g. Scandinavia. Compared to the self-supporting h-frame tower this design normally has non-vertical legs. This detail is useful for distinguishing self-supporting towers from guyed towers in aerial imagery etc, since the guy wires are usually too thin to be directly visible in such imagery.|
|design||portal||A tower type having two (or more) vertical structures connected by a horizontal cross-beam. All conductors are supported between the vertical structures (unlike the h-frame tower). This design is mostly used as termination tower at substations. It can also be used if a line intersects with other power lines.|
|Two and three level versions of the portal tower.|
|design||guyed_v-frame||A guyed tower type that is mainly used for ultra-high voltage lines e.g. in North America.|
|design||bipole||A pair of closely spaced but non-touching pylons. The conductors are typically mounted between the pylons. There are no cross-arms. Known as 'Wintrack' in the Netherlands. The bipole should be mapped as a single tower.|
|design||monopolar||A tower having no cross-arms, with insulators mounted on the tower itself. Mostly used as an anchor tower at very high voltage.This tower type is typically used in groups of three, with each carrying one phase, but may carry all phases in one tower. There are two recommended options for mapping such a group. Either map all three towers and connect the power line to the middle tower. Or map only one tower and add the attribute triple_tower=yes to the tower.|
|design:name||*||When the tower design has been given a specific name by its designer it can be indicated by this tag, such as Wintrack (The Netherlands), Eagle (Denmark).|
|design:incomplete||yes||An incomplete tower carries less conductors than the design is capable of. Sometimes the unused cross-arms are omitted (but can be retrofitted if an extra circuit is to be mounted)|
Some designs uses guying. For mapping these objects, see Tag:man made=guy.
This tag describes the functional type or role of the transmission tower, such as anchor tower. Please note that the tower:type=* tag has other meanings when used in combination with man_made=tower or man_made=mast.
|tower:type||suspension||A tower which supports the conductors vertically using suspension insulators. This is the default type and need not be tagged. However it may be useful to tag a suspension tower if it is used as an angle tower (an anchor tower would normally be expected here)|
|tower:type||anchor||A tower where conductor sections terminate at strain insulators. It is normally built stronger than suspension towers. Mostly used as angle tower when the line changes direction.|
|tower:type||termination||A tower with strain insulators used at the end of a line, for example at a substation or at the transition to an underground cable (add location:transition=yes). Designed to resist the full one-sided tension of the conductors.|
|tower:type||branch||A line branch starts at this tower. If the branch line is a cable then add location:transition=yes. The branching can take different forms which can be indicated by the following tags.
|tower:type||transposing||A tower in which the conductors exchange positions in order to balance the capacitance and impedance of the conductors.|
|tower:type||crossing||A special tower used at river crossings etc where a very long span or a large clearance is required. These towers may be very tall and are therefore significant landmarks.|
|location:transition||yes||This attribute denotes that one or more circuits transition to an underground cable in this tower. The cable terminals are located in the tower itself (no fenced area on the ground). The key location:transition=* replaces the values tower=transition and tower=air_to_ground which should no longer be used. |
For fenced transition stations with cable terminals on the ground use power=substation and substation=transition
ref=峨眉-中寮線 170;龍潭-中寮線 231?