|要素 : Zh-hans:Lanes|
|To tag individual lanes of a road together with their distinctive properties.|
:lanes can be used to tag individual lanes of a road.
The similar main key lanes=* counts the number of traffic lanes.
Lane-specific information can be expressed on a way by suffixing the key with
:lanes. This suffix is applicable to any existing
<key>=<value> tag pair. The value of that tag then contains the values for each lane separated by a | (vertical bar) in left-to-right order as viewed in the respective driving direction of those lanes. If the value of a specific lane is left blank, the (possibly assumed/implicit) value of the main key without
:lanes-suffix applies (the so called default value).
In the common case of two driving directions either
:backward is added to the end of the key; i.e.,
<key>:lanes:forward describes the properties of the lanes in the same direction as the osm-way, whereas
<key>:lanes:backward described the properties of the lanes in the opposite direction of the osm-way.
Please be aware that this extension covers all kinds of lanes for all kind of vehicles and is not restricted to motorized traffic.
In principle every tag used to describe properties of a road can be extended by the
:lanes suffix when its value depends on the lane. Following list gives an overview of potentially useful combinations and a short description when they might be needed:
|Road property||Lane specific key||Description|
||Useful if access depends on the lane: For example lanes can be restricted to buses (|
||Can be used for roads where the maximum allowed speed depends on the lane. See example below.|
||Allows description of designated turn lanes or which lanes will merge in the direction of travel. See detailed examples below.|
||Useful for roads where some lanes require a minimum speed or where lanes have different minimum speed.|
||Lane dependent surfaces, for example if there is cobblestone on the outer lane|
||While the road specific key describes the direction of the highway by using the name of the city the highway is heading to, the |
||Where necessary, the width of lanes can be tagged. As usual |
||A height restriction may vary from one lane to another if the road passes beneath an overpass that is inclined or arched.|
||If one or more lanes of the road are restricted to high-occupancy vehicles (typically vehicles with 2+ occupants, although this varies by jurisdiction). Most useful if entrance/egress is permitted at any point along the route; if entering or exiting the HOV lane(s) is only permitted at certain locations, modeling the HOV lane(s) as separate ways is preferable.|
Different maxspeed per lane (with/without default values)
A simple lane dependent
maxspeed example with road sign (one-way street and a general speed limit of 100 assumed):
|Without the use of default values:
lanes=3 oneway=yes maxspeed:lanes=100|100|80
|Using default values:
lanes=3 oneway=yes maxspeed=100 maxspeed:lanes=||80
Considering backward compatibility it might be preferred to tag this using default values.
Two driving directions
In the common case of two driving directions either
:backward is added to the end of the key.
lanes=6 lanes:forward=3 lanes:backward=3 hgv:lanes:forward=no|yes|yes hgv:lanes:backward=no|yes|yes
This is a road with three lanes in each direction and heavy good vehicles are prohibited on the leftmost lane in each direction.
The lanes are viewed in the respective driving direction; i.e.,
hgv:lanes:forward describes the lanes in the same direction as the osm-way. The first lane-value refers to the leftmost lane in this direction. Whereas
hgv:lanes:backward describes the lanes in the opposite direction of the osm-way.
Road with a sign-posted minimum speed, which applies to one lane only. Can be tagged as:
lanes=3 lanes:forward=2 lanes:backward=1 minspeed:lanes:forward=50|
Please note the final
| character in the value of
minspeed:lanes:forward: Because the right-most lane has no minimum speed, no value should be tagged after the lane separator.
Motorway with lanes and destinations
The following example demonstrates tagging of a motorway.
|Left part: lanes=3 |
Right part: lanes=1
|Left part: lanes=2 |
Right part: lanes=2
|lanes=4 (**) |
* These tags show how to add more than one value to a single lane, by separating those values with a ; (semi-colon).
** There is no physical separation between the upper two lanes and the lower ones, just a double solid line. While the editing standards recommend to split the ways only when a physical separation is present, in many regions the ways are already splitted in case of a legal separation like a double solid line. In such a case both resulting ways should be tagged with lanes=2.
Crossing with a designated lane for bicycles
lanes=3 turn:lanes=left|through|through|right vehicle:lanes=yes|yes|no|yes bicycle:lanes=yes|no|designated|yes cycleway:lanes=none|none|lane|none
Pay attention to the value of the lanes=* key. The number of lanes is referred to the lanes available to the traffic using the main highway=* key, in this example and also by definition of lanes=* key motorized traffic, what excludes bicycle lanes. See the proposal of the :lanes suffix for further explanation.
Note: Access tags, like "
bicycle:lanes", depend on the country and other circumstances:
bicycle:lanes=yes|no|designated|yes" value is result of fact that in this case bicycles are obligated to use bicycle lane in certain circumstances (e.g. as long as cyclist is not turning left or right or the cycle way is obstructed or otherwise not practicable, or the bike is too wide (e.g. trailer) and would encumber other cyclists). In other countries where use of bicycle lane is not fully obligatory for cyclists, like in Germany, tagging may be "
Designated Motorcycle Lanes
When tagging lanes you should only be counting lanes=* that are wide enough to fit a car (if it could fit a smart car or it's borderline then most likely you should still count it.)
1 and 2 can both take motor_vehicles, but lanes 3 and 4 cannot.
Motorcycles can use lanes 2, 3, and 4.
Lanes 3 and 4 are designated as motorcycle lanes.
lanes = 2 motorcycle:lanes=no|yes|designated|designated
If there is additional signage indicating that the left two lanes are for motor vehicles and the right two are not.
The style Lane and Road Attributes visualizes, amongst others, a variety of lane-dependent tags directly while editing, and also detects some common tagging mistakes like e.g. inconsistent number of lane-dependent values. The image below shows a road tagged with the keys turn:lanes=*, width:lanes=* and placement=*.